Hyundai Tucson: Front Axle Assembly / Front Hub / Knuckle / Tone Wheel Repair procedures

Hyundai Tucson (LM) 2010-2015 Service Manual / Driveshaft and axle / Front Axle Assembly / Front Hub / Knuckle / Tone Wheel Repair procedures

Removal

Remove the front wheel and tire (A) from front hub .

Tightening torque:

88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)

Be careful not to damage to the hub bolts when removing the front wheel and tire (A).

Remove the brake caliper mounting bolts, and then place the brake caliper assembly (A) with wire.

Tightening torque:

78.4 ~ 98.0 N.m (8.0 ~ 10.0 kgf.m, 57.8 ~ 72.3 lb-ft)

Remove the coking nut (A).

Tightening torque:

294.2 ~ 313.8 N.m (30.0 ~ 32.0 kgf.m, 217.0 ~ 231.5 lb-ft)

•	The front hub coking nut should be replaced with new ones.

•	After installation coking nut (A), stake the coking nut using a chisel and hammer as shown in the illustration below.

Remove the brake hose (A) and wheel speed sensor (B).

Tightening torque:

6.8 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 7.9 lb-ft)

Remove the tie rod end ball joint (C) from the knuckle.

(1)	Remove the split pin (A).

(2)	Remove the castle nut (B).

Tightening torque:

23.5 ~ 33.3 N.m (2.4 ~ 3.4 kgf.m, 17.4 ~ 24.6 lb-ft)

Remove the lower arm (A) mounting bolt and nut from the knuckle.

Tightening torque:

98.0 ~ 117.6 N.m (10.0 ~ 12.0 kgf.m, 72.3 ~ 86.7 lb-ft)

Loosen the strut mounting bolts (A) and then remove the hub and knuckle assembly from the strut assembly (B).

Tightening torque:

137.2 ~ 156.9N.m (14.0 ~ 16.0kgf.m, 101.2 ~115.7 Ib-ft)

Install in the reverse order of removal.

•	Use a SST (09581-11000) when installing the brake caliper assembly. (Refer to Brake System - "Front Disc Brake")

9.	Check the front alignment. (Refer to Suspension System - "Front Alignment")

Inspection

1.	Check the hub for cracks and the splines for wear.

2.	Check the brake disc for scoring and damage.

3.	Check the knuckle for cracks

4.	Check the bearing for cracks or damage.

Disassembly

1.	Using the snap ring pliers, remove the snap ring (A).

Remove the hub assembly from the knuckle assembly.

(1)	Install the front knuckle assembly (A) on press.

(2)	Lay a suitable adapter (B) upon the hub assembly shaft.

3.	Remove the dust cover (A).

Remove the hub bearing inner race from the hub assembly

(1)	Install a suitable tool (A) for removing the hub bearing inner race on the hub assembly.

(2)	Lay the hub assembly and tool (A) upon a suitable adapter (B).

(3)	Lay a suitable adapter (C) upon the hub assembly shaft.

(4)	Remove the hub bearing inner race (D) from the hub assembly by using press.

Remove the hub bearing outer race from the knuckle assembly.

(1)	Lay the hub assembly (A) upon a suitable adapter (B).

(2)	Lay a suitable adapter (C) upon the hub bearing outer race.

(3)	Remove the hub bearing outer race from the knuckle assembly by using press.

6.	Replace hub bearing with a new one.

Reassembly

1.	Install the dust cover (A).

Install the hub bearing to the knuckle assembly.

(1)	Lay the knuckle assembly (A) on press.

(2)	Lay a new hub bearing upon the knuckle assembly (A).

(3)	Lay a suitable adapter (B) upon the hub bearing.

(4)

Install the hub bearing to the knuckle assembly by using press.

Do not press against the inner race of the hub bearing because that can cause damage to the bearing assembly.

Always use a new wheel bearing assembly.

Install the hub assembly to the knuckle assembly.

(1)	Lay the hub assembly (A) upon a suitable adapter (B).

(2)	Lay the knuckle assembly (C) upon the hub assembly (A).

(3)	Lay a suitable adapter (D) upon the hub bearing.

(4)

Install the hub assembly (A) to the knuckle assembly (C) by using press.

Do not press against the inner race of the hub bearing because that can cause damage to the bearing assembly.

4.	Install the snap ring (A).

Front Hub / Knuckle / Tone Wheel Components and Components Location

Components 1. Split pin2. Driveshaft nut 3. Brake disc4. Hub5. Wheel bearing6. Snap ring7. Dust cover8. Knuckle9. Driveshaft ...

Driveshaft Assembly

...

Other information:

Hyundai Tucson (LM) 2010-2015 Service Manual: Battery Description and Operation
Description 1. The CMF(Closed Maintenance Free) battery is, as the name implies, totally maintenance free and has no removable battery cell caps. 2. The CMF(Closed Maintenance Free) battery does not require water replenishment for the repair. 3. The battery is completely sealed, exce ...

Hyundai Tucson (LM) 2010-2015 Service Manual: Rear Bumper Repair procedures
Replacement • Put on gloves to protect your hands. • When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage. • Take care not bend or scratch the cover and other parts. 1. After loosening the mounting screws, then re ...