Hyundai Tucson: Brake System / Rear Disc Brake Repair procedures

Removal
1.
Remove the rear wheel & tire.

Tightening torque :
88.3 ~ 107.9 N.m(9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

2.
Remove the upper arm by loosen the rear upper arm bolt (A) and nut (B). [2WD Only]

Tightening torque :
137.2 ~ 156.9N.m (14.0 ~ 16.0kgf.m, 101.2 ~115.7 lb-ft)

3.
Loosen the guide rod bolt (B) and pivot the caliper (A) up out of the way.

Tightening torque :
21.6 ~31.4 N.m (2.2 ~3.2 kgf.m, 15.9 ~23.1 lb-ft)

4.
Replace pad shim (D), pad retainers (C) and brake pads (B) in the caliper bracket (A).

5.
Loosen the hose eyebolt (B) and caliper mounting bolts (C), then remove the rear caliper assembly (A).

Tightening torque :
Brake hose to caliper (B) :
24.5 ~ 29.4 N.m (2.5 ~ 3.0 kgf.m, 18.1 ~ 21.7 lb-ft)
Caliper assembly to carrier (C) :
49.0 ~ 58.8 N.m (5.0 ~ 6.0 kgf.m, 36.2 ~ 43.4 lb-ft)

Replacement
Rear brake pads
1.
Loosen the guide rod bolt (B) and pivot the caliper (A) up out of the way.

Tightening torque:
21.6 ~31.4 N.m (2.2 ~3.2 kgf.m, 15.9 ~23.1 lb-ft)

2.
Replace pad shim (D), pad retainers (C) and brake pads (B) in the caliper bracket (A).

Inspection
Rear Brake Disc Thickness Check
1.
Check the brake pads for wear and fade.
2.
Check the brake disc for damage and cracks.
3.
Remove all rust and contamination from the surface, and measure the disc thickness at 8 points, at least, of same distance (5mm) from the brake disc outer circle.

Brake disc thickness
Standard: 10 mm (0.39 in)
Service limit: 8.4 mm (0.33 in)
Deviation: less than 0.005 mm (0.0002 in)

4.
If wear exceeds the limit, replace the discs and pad assembly left and right of the vehicle.
Rear Brake Pad Check
1.
Check the pad wear. Measure the pad thickness and replace it, if it is less than the specified value.

Pad thickness
Standard value: 10 mm (0.393 in)
Service limit: 2.0 mm (0.0787 in)

2.
Check that grease is applied, to sliding contact points and the pad and backing metal for damage.
Rear Brake Disc Runout Check
1.
Place a dial gauge about 5mm (0.2 in.) from the outer circumference of the brake disc, and measure the runout of the disc.

Brake disc runout
Limit: 0.05 mm (0.00197 in.) or less (new one)

2.
If the runout of the brake disc exceeds the limit specification, replace the disc, and then measure the runout again.
3.
If the runout exceeds the limit specification, install the brake disc after turning it 180° and then check the runout of the brake disc again.
4.
If the runout cannot be corrected by changing the position of the brake disc, replace the brake disc.
Installation
1.
Installation is the reverse of removal.
2.
Use a SST (09581-11000) when installing the brake caliper assembly.

3.
After installation, bleed the brake system.
(Refer to Brake system bleeding)
Rear Disc Brake Components and Components Location
Components 1. Guide rod bolt2. Bleed screw3. Caliper bracket4. Caliper body5. Inner pad shim6. Brake pad7. Pad retainer ...

Parking Brake System
...

Other information:

Hyundai Tucson (LM) 2010-2015 Service Manual: Power Window Switch Repair procedures
Inspection Main Power Window Switch Inspection 1. Disconnect the negative (-) battery terminal. 2. Remove the front door trim and power window switch. (Refer to the BD group - "Front door") 3. Check for continuity between the terminals in each switch position according to the table. ...

Hyundai Tucson (LM) 2010-2015 Service Manual: Smart Parking Assist System Sensor Repair procedures
Removal Front SPAS sensor 1. Remove the front bumper. (Refer to the BD group - "Front bumper") 2. Pull out the SPAS sensor (A) by opening the sensor holder out. 3. Disconnect the connector form the sensor. Rear SPAS sensor 1. Lift the vehicle up by using Remove the front bumper. ...

© 2010-2024 www.htmanual.net