Hyundai Tucson: Heater / Heater Unit Repair procedures

Hyundai Tucson (LM) 2010-2015 Service Manual / Heating, Ventilation and Air Conditioning / Heater / Heater Unit Repair procedures

Replacement

1.	Disconnect the negative (-) battery terminal.

2.	Recover the refrigerant with a recovery/ recycling/ charging station.

3.	When the engine is cool, drain the engine coolant from the radiator.

4.	Remove the expansion valve cover (A).

Remove the bolts (A) and the expansion valve (B) from the evaporator core.

Plug or cap the lines immediately after disconnecting them to avoid moisture and dust contamination.

Tightening torque :

7.8 ~ 11.7 N.m ( 0.8 ~ 1.2 kgf.m, 5.7 ~ 8.6 Ib-ft)

Disconnect the inlet (C) and outlet (D) heater hoses from the heater unit.

Engine coolant will run out when the hoses are disconnected; drain it into a clean drip pan. Be sure not to let coolant spill on electrical parts or painted surfaces. If any coolant spills, rinse it off immediately.

7.	Remove the crash pad (Refer to BD group-crash pad).

8.	Disconnect the connectors from the temperature control actuator, the mode control actuator and the evaporator temperature sensor.

9.	Remove the cowl cross bar assembly. (Refer to BD group-cowl cross bar)

10.	Remove the heater & blower unit after loosening 3 mounting bolts.

11.	Remove the blower unit (B) from heater unit after loosening 3 screws.

12.

Install in the reverse order of removal, and note these items :

A.	If you're installing a new evaporator, add refrigerant oil (ND-OIL8).

B.	Replace the O-rings with new ones at each fitting, and apply a thin coat of refrigerant oil before installing them. Be sure to use the right O-rings for R-134a to avoid leakage.

C.	Immediately after using the oil, replace the cap on the container, and seal it to avoid moisture absorption.

D.	Do not spill the refrigerant oil on the vehicle ; it may damage the paint ; if the refrigerant oil contacts the paint, wash it off immediately

E.	Apply sealant to the grommets.

F.	Make sure that there is no air leakage.

G.	Charge the system and test its performance.

H.	Do not interchange the inlet and outlet heater hoses and install the hose clamps securely.

I.	Refill the cooling system with engine coolant

Heater Unit Components and Components Location

Component Location Components 1. Heater Case (LH)2. Heater Core Cover3. Mode Actuator4. Shower Duct (LH)5. Temp Actuator (Drive)6. Evaporator Sensor7. Def Door Lever8. Vent Door Lever9. Foot Sub ...

Heater Core Repair procedures

Replacement 1. Remove the crash pad. (Refer to Heater - "Heater Unit") 2. Loosen the mounting screw and then remove the heater core cover (A). 3. Remove the heater core. 4. Be carefu ...

Other information:

Hyundai Tucson (LM) 2010-2015 Service Manual: Steering Column and Shaft Repair procedures
Replacement 1. Disconnect the battery negative cable from the battery and then wait for at least 30 seconds. 2. Turn the steering wheel so that the front wheels can face straight ahead. 3. Remove the airbag module (A). (Refer to Restraint - "Airbag Module") 4. Disconnect the connect ...

Hyundai Tucson (LM) 2010-2015 Owners Manual: Memory fuse (SHUNT connector)
Your vehicle is equipped with a memory fuse (SHUNT connector) to prevent battery discharge if your vehicle is parked without being operated for prolonged periods. Use the following procedures before parking the vehicle for prolonged periods. 1. Turn off the engine. 2. Turn off the headligh ...