Hyundai Tucson: ESC(Electronic stability system) System / ESC Control Unit Repair procedures

Removal
1.
Turn the ignition switch OFF.
2.
Disconnect the brake tubes from the HECU by unlocking the nuts counterclockwise with a spanner.

Tightening torque :
ABS : 12.7 ~ 16.7N.m(1.3 ~ 1.7kgf.m, 9.4 ~ 12.3lb-ft)
ESC : 18.6 ~ 22.6N.m(1.9 ~ 2.3kgf.m, 13.7 ~ 16.6lb-ft)

[LHD]

[RHD]

3.
Pull up the lock of the HECU connector , then disconnect the connector.
4.
Loosen the HECU bracket bolts (A) and nut (B), then remove HECU and bracket.

Tightening torque :
16.7 ~ 25.5N.m(1.7 ~ 2.6kgf.m, 12.3 ~ 18.8lb-ft)

[LHD]

[RHD]

   
1.
Never attempt to disassemble the HECU.
2.
The HECU must be transported and stored in.
3.
Never shock to the HECU.
5.
Remove the 3 bolts, then remove the bracket from HECU.

Tightening torque :
10.8 ~ 13.7N.m(1.1 ~ 1.4kgf.m, 8.0 ~ 10.1lb-ft)

Installation
1.
Installation is the reverse of removal.
2.
Tighten the HECU mounting bolts and nuts to the specified torque.
3.
After installation, bleed the brake system.
(Refer to ABS bleeding)
4.
Variant coding.
2WD and 4WD vehicle are sharing the HECU each other. To apply appropriate vehicle, HECU needs to variant coding process.
Variant coding process is necessary when :
A.
HECU is replaced.
B.
C1702 DTC(variant coding error) code is detected.
Perform the Variant coding.

5.
Perform the Longitudinal Sensor Calibration.
(Refer to ESC (Electronic stability system) - "Longitudinal G Sensor")
[Auto Detected Sensor Calibration]

[Hill Start Assist Control Setting]

[Longitudinal G Sensor Calibration]

ESC Control Unit Components and Components Location
Components (1) 1. Front - left tube2. Rear - right tube3. Rear - left tube4. Front - right tube5. MC26. MC17. ESC control module connector8. ESC control module(HECU)9. Damper10. Bracket Componen ...

Yaw-rate and G Sensor Description and Operation
Description When the vehicle is turning with respect to a vertical axis the yaw rate sensor detects the yaw rate electroniclly by the vibration change of plate fork inside the yaw rate sensor. ...

Other information:

Hyundai Tucson (LM) 2010-2015 Service Manual: Heater Unit Components and Components Location
Component Location Components 1. Heater Case (LH)2. Heater Core Cover3. Mode Actuator4. Shower Duct (LH)5. Temp Actuator (Drive)6. Evaporator Sensor7. Def Door Lever8. Vent Door Lever9. Foot Sub Lever10. Def Door11. Vent Door (LH)12. Foot Door13. Mix Door (LH)(Auto Type)14. Heater Core15. Duct ...

Hyundai Tucson (LM) 2010-2015 Service Manual: Pressure Sensor Description and Operation
Description The 4WD ECU makes a Motor Pump(Actuator) turn round for generating an oil pressure. And then it presses a multiple disk clutch and transfers the generated torque into rear wheels. Its torque value varies according to a pressure status. ...

© 2010-2024 www.htmanual.net