Hyundai Tucson: Driveshaft Assembly / Front Driveshaft Repair procedures

Hyundai Tucson (LM) 2010-2015 Service Manual / Driveshaft and axle / Driveshaft Assembly / Front Driveshaft Repair procedures

Removal

Remove the front wheel and tire (A) from front hub .

Tightening torque:

88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)

Be careful not to damage to the hub bolts when removing the front wheel and tire (A).

Remove the coking nut (A).

Tightening torque:

294.2 ~ 313.8 N.m (30.0 ~ 32.0 kgf.m, 217.0 ~ 231.5 lb-ft)

•	The front hub coking nut should be replaced with new ones.

•	After installation coking nut (A), stake the coking nut using a chisel and hammer as shown in the illustration below.

Remove the brake hose (A) and wheel speed sensor (B).

Tightening torque:

6.8 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 7.9 lb-ft)

Remove the tie rod end ball joint (C) from the knuckle.

(1)	Remove the split pin (A).

(2)	Remove the castle nut (B).

Tightening torque:

23.5 ~ 33.3 N.m (2.4 ~ 3.4 kgf.m, 17.4 ~ 24.6 lb-ft)

Remove the lower arm (A) mounting bolt and nut from the knuckle.

Tightening torque:

98.0 ~ 117.6 N.m (10.0 ~ 12.0 kgf.m, 72.3 ~ 86.7 lb-ft)

6.	Using a plastic hammer (A), disconnect driveshaft (C) from the axle hub (B).

Loosen the inner shaft mounting bolts and then disconnect the inner shaft (A).

Tightening torque:

49.0 ~ 68.6 N.m (5.0 ~ 7.0 kgf.m, 36.2 ~ 50.6 lb-ft)

By the shape and the engine bracket bolts are mounted differently.

8.	Insert a pry bar (A) between the transaxle case and joint case, and separate the drive shaft (B) from the transaxle case.

Install in the reverse order of removal.

•	Use a pry bar being careful not to damage the transaxle and joint.

•	Do not insert the pry bar too deep, as this may cause damage to the oil seal.

•	Do not pull the driveshaft by excessive force it may cause components inside the joint kit to dislodge resulting in a torn boot or a damaged bearing.

•	Plug the hole of the transaxle case with the oil seal cap to prevent contamination.

•	Support the driveshaft properly.

•	Replace the retainer ring whenever the driveshaft is removed from the transaxle case.

10.	Check the front alignment. (Refer to Suspension System - "Front Alignment")

Front Driveshaft Components and Components Location

Components [THETA II 2.4 2WD] 1. Driveshaft (LH)2. Driveshaft (RH) [NU 2.0 / THETA II 2.4 4WD] 1. Driveshaft (LH)2. Inner shaft bearing bracket3. Driveshaft (RH) Components [LH] ...

TJ Joint Components and Components Location

Components [LH] 1. BJ assembly 2. BJ circlip 3. BJ boot band 4. BJ boot 5. Shaft6. TJ boot band7. TJ boot8. Spider assembly9. Retainer ring10. TJ housing11. Housing circlip [RH] 1. BJ ...

Other information:

Hyundai Tucson (LM) 2010-2015 Owners Manual: Roof rack
If the vehicle has a roof rack, you can load cargo on top of your vehicle. The following specification is the maximum weight that can be loaded onto the roof rack. Distribute the load as evenly as possible onto the roof rack and secure the load firmly. ✽ NOTICE If the vehicle i ...

Hyundai Tucson (LM) 2010-2015 Service Manual: Crankshaft Position Sensor (CKPS) Description and Operation
Description Crankshaft Position Sensor (CKPS) detects the crankshaft position and is one of the most important sensors of the engine control system. If there is no CKPS signal input, the engine may stop because of CKPS signal missing. This sensor is installed in ladder frame and generates ...