Hyundai Tucson: Charging System / Alternator Repair procedures

Hyundai Tucson (LM) 2010-2015 Service Manual / Engine Electrical System / Charging System / Alternator Repair procedures

Removal

1.	Turn ignition switch OFF and disconnect the negative (-) battery cable.

2.	Remove the drive belt. (Refer to Engine Mechanical System - "Drive Belt")

3.	Disconnect the alternator connector (A) and the cable (B) from alternator "B" terminal.

4.	Pull out the through bolt and then remove the alternator (A).

Installation

1.	Install in the reverse order of removal.

Adjust the alternator belt tension after installation.

(Refer to Engine Mechanical System - "Drive Belt")

Alternator installation bolt:

[M10] 29.4 ~ 41.2 N.m (3.0 ~ 4.2 kgf.m, 21.7 ~ 30.4 Ib-ft)

[M8] 21.6 ~ 32.4 N.m (2.2 ~ 3.3 kgf.m, 15.9 ~ 23.9 Ib-ft)

Alternator brace mounting bolt:

21.6 ~ 32.4 N.m (2.2 ~ 3.3 kgf.m, 15.9 ~ 23.9 Ib-ft)

Disassembly

1.	Remove the rear cover (A) after removing nuts (B).

2.	Remove the mounting bolts (A) and the regulator assembly (B).

3.	Remove the slip ring guide (A) after pulling it.

Remove the OAD(Overrunning Alternator Decoupler) cap.

•	When installing, replace with new OAD cap.

5.	Remove the OAD(Overrunning Alternator Decoupler) pulley (A) using the special tool.

6.	Unsolder the 3 stator leads (A).

7.	Remove the 4 through bolts (A).

8.	Disconnect the rotor (A) and housing (B).

Reassembly

Reassemble in the reverse order of disassembly.

•	When reassembling OAD pulley, replace with new OAD cap.

Inspection

[Rotor]

1.	Check that there is continuity between the slip rings (C).

2.	Check that there is no continuity between the slip rings and the rotor (B) or rotor shaft (A).

3.	If the rotor fails either continuity check, replace the alternator.

[Stator]

1.	Check that there is continuity between each pair of leads (A).

2.	Check that there is no continuity between each lead and the coil core.

3.	If the coil fails either continuity check, replace the alternator.

Alternator Schematic Diagrams

Circuit Diagram • COM signal - When controlling the voltage generated, the ECM sends the target voltage data to the alternator via a PWM signal.(High voltage: 4V or h ...

Battery Description and Operation

Description 1. The CMF(Closed Maintenance Free) battery is, as the name implies, totally maintenance free and has no removable battery cell caps. 2. The CMF(Closed Maintenance Free) batter ...

Other information:

Hyundai Tucson (LM) 2010-2015 Owners Manual: Fog light bulbs
1. Remove the front bumper under cover. 2. Reach your hand into the back of the front bumper. 3. Disconnect the power connector from the socket. 4. Remove the bulb-socket from the housing by turning the socket counter clockwise until the tabs on the socket align with the slots on the housing. ...

Hyundai Tucson (LM) 2010-2015 Service Manual: Injector Repair procedures
Inspection 1. Turn the ignition switch OFF. 2. Disconnect the injector connector. 3. Measure resistance between the injector terminals 1 and 2. 4. Check that the resistance is within the specification. Specification: Refer to “Specification” Removal ...