Hyundai Tucson: General Information / Troubleshooting

Troubleshooting
Symption
Suspect area
Remedy
Engine misfire with abnormal internal lower engine noises
Worn crankshaft bearings
Loose or out of specification engine flywheel
Replace the crankshaft and bearings as required.
Repair or replace the flywheel as required.
Worn piston rings
(Oil consumption may or may not cause the engine to misfire.)
Inspect the cylinder for a loss of compression.
Repair or replace as required.
Worn crankshaft thrust bearings
Replace the crankshaft and bearings as required
Engine misfire with abnormal valve train noise
Stuck valves
(Carbon buidup on the valve stem)
Repair or replace as required.
Excessive worn or mis-aligned timing chain
Replace the timing chain and sprocket as required.
Worn camshaft lobes
Replace the camshaft.
Engine misfire with coolant consumption
Faulty cylinder head gasket or other damage to the cylinder head and engine block cooling system
Coolant consumption may or may not cause the engine to overheat
Inspect the cylinder head and engine block for damage to the coolant passages and/or a faulty head gasket.
Repair or replace as required.
Engine misfire with excessive oil consumption
Worn valves, guides and/or valve stem oil seals
Repair or replace as required.
Worn piston rings
(Oil consumption may or may not cause the engine to misfire)
Inspect the cylinder for a loss of compression.
Repair or replace as required.
Engine noise on start-up, but only lasting a few seconds
(Check and compare with known good vehicle to determine normal condition.)
Incorrect oil viscosity
Drain the oil.
Install the correct viscosity oil.
Worn crankshaft thrust bearing
Inspect the thrust bearing and crankshaft.
Repair or replace as required.
Upper engine noise, regardless of engine speed
Low oil pressure
Repair or replace as required.
Broken valve spring
Replace the valve spring.
Worn or dirty valve lifters
Replace the valve lifters.
Stetched or broken timing chain and/or damaged sprocket teeth
Replace the timing chain and sprockets.
Worn timing chain tensioner, if applicable
Replace the timing chain tensioner as required.
Worn camshaft lobes
Inspect the camshaft lobes.
Replace the camshaft as required.
Worn valve guides or valve stems
Inspect the valves and valve guides, then repair or replace as required.
Stuck valves (Carbon on the valve stem or valve seat may cause the valve to stay open.)
Inspect the valves and valve guides, then repair or replace as required.
Worn drive belt, idler, tensioner and bearing
Replace as required.
Lower engine noise, regardless of engine speed
Low oil pressure
Repair or required.
Loose or damaged flywheel
Repair or replace the flywheel.
Damaged oil pan, contacting the oil pump screen
Inspect the oil pan.
Inspect the oil pump screen.
Repair or replace as required.
Oil pump screen loose, damaged or restricted
Inspect the oil pump screen.
Repair or replace as required.
Excessive piston-to-cylinder bore clearance
Inspect the piston, piston pin and cylinder bore.
Repair or replace as required.
Excessive piston pin-to-piston clearance
Inspect the piston, piston pin and the connecting rod.
Repair or replace as required.
Excessive connecting rod bearing clearance
Inspect the following components and repair or replace as required.
The connecting rod bearings.
The connecting rods.
The crankshaft pin journals.
Excessive crankshaft bearing clearance
Inspect the following components, and repair or replace as required.
The crankshaft bearings.
The crankshaft main journals.
The cylinder block
Incorrect piston, piston pin and connecting rod installation
Verify the piston pins and connecting rods are installed correctly.
Repair as required.
Engine noise under load
Low oil pressure
Repair or replace as required.
Excessive connecting rod bearing clearance
Inspect the following components and repair or replace as required:
The connecting rod bearings
The connecting rods
The crankshaft
Excessive crankshaft bearing clearance
Inspect the following components, and repair or replace as required:
The crankshaft bearings
The crankshaft main journals
The cylinder block
Engine is not cranked.
Crankshaft does not rotate.
Hydraulically locked cylinder
Coolant/antifreeze in cylinder
Oil in cylinder
Fuel in cylinder
1.
Remove spark plugs and check for fluid.
2.
Inspect for broken head gasket.
3.
Inspect for cracked engine block or cylinder head.
4.
Inspect for a sticking fuel injector and/or leaking fuel regulator.
Broken timing chain and/or timing chain gears
1.
Inspect timing chain and gears.
2.
Repair as required.
Material in cylinder
Broken valve
Piston material
Foreign material
1.
Inspect cylinder for damaged components and/or foreign materials.
2.
Repair or replace as required.
Seized crankshaft or connecting rod bearings
1.
Inspect crankshaft and connecting rod bearing.
2.
Repair as required.
Bent or broken connecting rod
1.
Inspect connecing rods.
2.
Repair as required.
Broken crankshaft
1.
Inspect crankshaft.
2.
Repair as required.

Repair procedures
Compression Pressure Inspection     If the there is lack of power, excessive oil consumption or poor fuel economy, measure the compression pressure. 1. Warm up and stop engine ...

Special Service Tools
Special Service Tools Tool (Number and name)IllustrationUseCrankshaft front oil seal installer(09231-2E000)Installation of the front oil seal 09231-2E000 (installer)Valve stem seal installer(0922 ...

Other information:

Hyundai Tucson (LM) 2010-2015 Owners Manual: Bluetooth® Wireless Technology Setting
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks is under license. Other trademarks and trade names are those of their respective owners. A Bluetooth® enabled cell phone is required to use Bluetooth® wireless technology. WAR ...

Hyundai Tucson (LM) 2010-2015 Service Manual: Description and Operation
Description This function describes the following features - Input detection by Auto Light Sensor. - Generate Auto Light Out Status data. - Send Auto Light Out Status. - Tail Lamp Control by Auto light Mode. - Head Lamp Low Control by Auto light Mode. - AV Tail Control ...

© 2010-2024 www.htmanual.net