Hyundai Tucson: Parking Brake System / Parking Brake Assembly Repair procedures

Removal
Parking Brake Pedal [Foot type]
1.
Remove the crash pad lower panel.
(Refer to Body - "Crash Pad")
2.
Remove the junction box.
(Refer to Body Electrical System - "Fuses and Relays")
3.
Disconnect the parking brake switch connector (A).

4.
Remove the parking brake pedal mounting bolts (A) and nut.(B)

5.
Remove the parking brake cable mounting bolts.
6.
Remove the parking brake cable adjusting nut (A) and the fixing clip (B), and then remove the parking brake pedal.

7.
Remove the floor console.
(Refer to Body - "Console")
8.
Remove the floor console bracket.

9.
Remove the paring brake cable fixing clip (A) and bolts.

10.
Loosen the adjusting nut (A) and then remove the front parking brake cable.

11.
Raise the vehicle, and make sure it is securely supported.
12.
Remove the parking brake cable (A) after removing the retaining ring (B).

13.
Loosen the parking brake cable bracket bolts and remove the rear parking brake cable.
Parking Brake Lever [Hand type]
1.
Remove the floor console.
(Refer to Body - "Console")
2.
Remove the floor console bracket.

3.
Disconnect the connector (A) of parking brake switch.
4.
Loosen the adjusting nut (A) and the parking brake cables.

5.
Remove the parking brake lever assembly after removing the 4 bolts (A) as shown below.

6.
Raise the vehicle and make sure it is securely supported.
7.
Remove the parking brake cable (A) after removing the retaining (B).

8.
Loosen the parking brake cable braket bolts and remove the parking brake cable.
Parking Brake Shoe [2WD]
1.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the rear tire and wheel.
3.
Remove the rear brake caliper and Rear disc brake.
(Refer to "Rear disc brake removal")
4.
Remove the parking brake cable (B), after removing the clip (A).

5.
Remove the shoe hold down pin (A) and the spring (B) by pressing and rotating the spring.

6.
Remove the adjuster assembly (B) and the lower return spring (A).

7.
Remove the upper return spring (C) and the brake shoes (D).
8.
Remove the operating lever assembly (E).
Parking Brake Shoe [4WD]
1.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the rear tire and wheel, then remove the brake caliper.
(Refer to "Rear disc brake removal")
3.
Remove the rear brake disc by loosening the screws (A).

4.
Remove the rear hub unit bearing (A).

5.
Remove the shoe hold down pin (A) and the spring (B) by pushing the retainer spring and turning the pin.

6.
Remove the adjuster assembly (A) and the return spring (B).

7.
Remove the parking brake cable (B) from the brake shoe (A).

8.
Remove the strut (C) and the strut spring (D).

9.
Remove the brake shoe.
10.
Remove the parking brake cable retaining (B), from the parking brake cable (A).

Installation
Parking Brake Shoe [2WD]
1.
Install the operating lever assembly (E).

2.
Install the upper return spring (C) and the brake shoes (D).
3.
Install the adjuster assembly (B) and the lower return spring (A).

4.
Install the shoe hold down pin (A) and spring (B) by pressing and rotating the spring.

5.
Install the parking brake cable (B), then install the clip (A).

6.
Install the rear brake disc, then adjust the rear brake shoe clearance.
(1)
Remove the plug from the disc.
(2)
Rotate the toothed wheel of adjuster by a screw driver until the disc is not moving, and then return it by 4 notches in the opposite direction.
7.
Install the brake caliper assembly.
(Refer to "Rear brake installation")
8.
Install the tire and wheel, after installing the plug on the disc.
9.
If the parking brake shoe or the brake disc are replaced a newly one, perform the brake shoe bed-in procedure.
(1)
Hand type - While operating the arking brake pedal for 68.6N (7kgf, 15.4 lbf) effort, drive the vehicle 500 meters (0.31 miles) at the speed of 30kph (18.6 mph).
Foot type - While operating the parking brake lever for 147N (15kgf, 33 lbf) effort, drive the vehicle 500 meters (0.31 miles) at the speed of 30kph (18.6 mph).
(2)
Repeat the above procedure more than three times.
(3)
Must be held on a 20% uphill.
   
After adjusting parking brake, notice following matter;
1.
Must be free from troubles when the parking pedal is operated at 686.5 N (70 kgf,154 lbf).
2.
Check that all parts move smoothly.
3.
The parking brake indicator lamp must be on after the parking pedal is worked and must be off after the pedal is released.
Parking Brake Shoe [4WD]
1.
Install the brake shoe (A) to the back plate (B).

2.
Install the shoe hold down pin (C) and the spring (D) by pushing the retainer spring (D) and turning the pins.
3.
After installing the strut (A) and upper return spring (B), install the adjuster assembly (C) and the lower return spring (D).

4.
Install the parking brake cable (A), then install the retaining (B).

5.
Apply a coating of the specified grease to each sliding parts of parking brake as shown.

Specified grease :
Multi purpose grease SAE J310, NLGI No.2

6.
Install the rear brake disc, then adjust the rear brake shoe clearance.
(1)
Remove the plug from the disc.
(2)
Rotate the toothed wheel of adjuster by a screw driver until the disc is not moving, and then return it by 4 notches in the opposite direction.
7.
Install the brake caliper.
(Refer to "Rear brake installation")
8.
Install the tire and wheel.
9.
If the parking brake shoe or the brake disc are replaced a newly one, perform the brake shoe bed-in procedure.
(1)
Hand type - While operating the arking brake pedal for 68.6N (7kgf, 15.4 lbf) effort, drive the vehicle 500 meters (0.31 miles) at the speed of 30kph ( 18.6 mph).
Foot type - While operating the parking brake lever for 147N (15kgf, 33 lbf) effort, drive the vehicle 500 meters (0.31 miles) at the speed of 30kph ( 18.6 mph).
(2)
Repeat the above procedure more than three times.
(3)
Must be held on at 20% uphill.
   
After adjusting parking brake, notice following matter;
1.
Must be free from troubles when the parking pedal is operated at 686.5 N (70 kgf, 154 lbf).
2.
Check that all parts move smoothly.
3.
The parking brake indicator lamp must be on after the parking pedal is worked and must be off after the pedal is released.
Parking Brake Lever [Hand Type]
1.
Install the parking brake lever assembly, then tighten the mounting bolts (A).

2.
Apply a coating of the specified grease to each sliding parts (A) of the ratchet plate or the ratchet pawl.

Specified grease :
Multi purpose grease SAE J310, NLGI No.2

3.
Install the parking brake cable adjuster, then adjust the parking brake lever stroke by turning adjusting nut (A).

Parking brake lever stroke :
6 cliks (Pull the lever with 20kgf)

   
After repairing the parking brake shoe, adjust the brake shoe clearance, and then adjust the parking brake lever stroke. (Refer to "Parking brake shoe installation")

4.
Release the parking brake lever fully, and check that parking brakes do not drag when the rear wheels are turned. Readjust if necessary.
5.
Make sure that the parking brakes are fully applied when the parking brake lever is pulled up fully.
6.
Reconnect the connector of parking brake switch.
   
Inspect the continuity of parking brake switch.

When the brake lever is pulled : continuity
When the brake lever is released : no continuity

7.
Install the floor console.
(Refer to Body - "Floor Console")
Parking Brake Pedal [Foot type]
1.
Install the parking brake cable.
2.
Install the holding clip (B) and the cable adjusting nut (A) after fixing the parking brake cable.

3.
Install the parking brake pedal, and then install the parking brake pedal mounting bolts (A) and nut (B).

4.
Adjust the parking brake pedal stroke by turning the adjusting nut (A).
(1)
Operate the parking brake pedal through a full stroke over 3 times for setting the parking cables.
(2)
Adjust the adjusting nut (A) for parking brake pedal stroke 4notches when operating effort is 196N(20kgf.44lb).

   
1.
The parking brake adjustment must be carried out after adjusting the rear shoe.
2.
After adjusting parking brake, notice following matter.
1)
Must be free from clearance between adjusting nut and pin.
2)
Check securely that the brake is not dragging.
5.
Reconnect the parking brake switch connector (A).

6.
Install the juncting box.
(Refer to Body Electrical System - "Fuses and Relays")
7.
Install the crash pad lower panel.
(Refer to Body - "Crash Pad")
Adjustment
Parking Brake Shoe Clearance Adjustment
1.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the rear tire and wheel.
3.
Remove the plug from the disc.

4.
Rotate the toothed wheel of adjuster by a screw driver until the disc is not moving, and then return it by 4 notches in the opposite direction.
5.
Install the rear wheel & tire after installing the plug on the disc.
Parking Brake Pedal Stroke Adjustment
1.
Operate the parking brake pedal through a full stroke over 3 times for setting the parking cables.
2.
Adjust the adjusting nut (A) for parking barke pedal stoke 4 notches when operating effort is 196N(20kgf, 44lbf)

   
1.
The parking brake adjustment must be carried out after adjusting the rear shoe.
2.
After adjusting parking brake, notice following matter.
1)
Must be free from clearance between adjusting nut and pin.
2)
Check securely that the brake is not dragging.
Parking Brake Lever Stroke Adjustment
1.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the floor console pad.
3.
Adjust the parking brake lever stroke by turning adjusting nut (A).

Parking brake lever stroke :
6 cliks (Pull the lever with 20kgf)

   
After repairing the parking brake shoe, adjust the brake shoe clearance, and then adjust the parking brake lever stroke. (Refer to "Parking brake shoe installation")

4.
Release the parking brake lever fully, and check that parking brakes do not drag when the rear wheels are turned. Readjust if necessary.
5.
Make sure that the parking brakes are fully applied when the parking brake lever is pulled up fully.
6.
Install the floor console.
Parking Brake Assembly Components and Components Location
Components (1) 1. Parking brake pedal2. Front parking brake cable (Foot type olny)3. Equalizer assembly4. Rear parking brake cable5. Parking brake lever assembly Components (2) 1. Back plat ...

ESC(Electronic stability system) System
...

Other information:

Hyundai Tucson (LM) 2010-2015 Service Manual: TPMS Receiver Description and Operation
Description 1. Mode (1) Virgin State A. The receiver as a sole part is shipped in this state. Replacement parts should therefore arrive in this state. B. In this state, there is no sensor monitoring and no DTC monitoring. C. The state indicates that platform specific parameters must ...

Hyundai Tucson (LM) 2010-2015 Owners Manual: To decrease cruise control speed
Push the lever (1) down (to SET-) and hold it. Your vehicle will gradually slow down. Release the lever at the speed you want to maintain. Push the lever (1) down (to SET-) and release it immediately. The cruising speed will decrease 1.0 mph (1.6 km/h) each time the lever is operated ...

© 2010-2024 www.htmanual.net