Hyundai Tucson: Airbag Module / Driver Airbag (DAB) Module and Clock Spring Repair procedures

Hyundai Tucson (LM) 2010-2015 Service Manual / Restraint / Airbag Module / Driver Airbag (DAB) Module and Clock Spring Repair procedures

Removal

1.	Disconnect the battery negative cable and wait for at least three minutes before beginning work.

2.	Remove the airbag module mounting bolts (2EA).

3.	Remove the wiring fixing clip (C) and disconnect the horn connector (A).

Release the connector locking pin, then disconnect the driver airbag module connector (B).

The removed airbag module should be stored in aclean, dry place with the pad cover facing up.

5.	Remove the steering wheel and steering wheel column cover. (Refer to the Steering System group- Steering Column and Shaft)

6.	Disconnect the clock spring and horn connector, then remove the clock spring.

Inspection

Driver Airbag (DAB)

If any improper parts are found during the following inspection, replace the airbag module with a new one.

Never attempt to measure the circuit resistance of the airbag module (squib) even if you are using the specified tester. If the circuit resistance is measured with a tester, accidental airbag deployment will result in serious personal injury.

1.	Check pad cover for dents, cracks or deformities.

2.	Check the airbag module for denting, cracking or deformation.

3.	Check hooks and connectors for damage, terminals for deformities, and harness for binds.

4.	Check airbag inflator case for dents, cracks or deformities.

5.	Install the airbag module to the steering wheel to check for fit or alignment with the wheel.

Clock Spring

1.	If, as a result of the following checks, even one abnormal point is discovered, replace the clock spring with a new one.

2.	Check connectors and protective tube for damage, and terminals for deformities.

Installation

1.	Remove the ignition key from the vehicle.

2.	Disconnect the battery negative cable from battery and wait for at least three minutes before beginning work.

3.	Connect the clock spring harness connector and horn harness connector to the clock spring.

4.	Set the center position by setting the marks between the clock spring and the cover into line. Make an array the mark (xx) by turning the clock spring clockwise to the stop and then 2.0 revolutions counterclockwise.

5.	Install the steering wheel column cover and the steering wheel. (Refer to the Steering System group- Steering Column and Shaft)

6.	Connect the Driver Airbag (DAB) module connector and horn connector, and then install the Driver Airbag (DAB) module on the steering wheel.

Secure the Driver Airbag (DAB) with the new mounting bolts.

Tightening torque:

7.8 ~ 10.8 N.m (0.8 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)

8.	Connect the battery negative cable.

After installing the airbag, confirm proper system operation:

A.	Turn the ignition switch ON; the SRS indicator light should be turned on for about six seconds and then go off.

B.	Make sure horn button works.

Driver Airbag (DAB) Module and Clock Spring Components and Components Location

Components 1. Driver Airbag (DAB)2. Steering Wheel3. Clock Spring ...

Passenger Airbag (PAB) Module Description and Operation

Description The passenger airbag (PAB) is installed inside the crash pad and protects the front passenger in the event of a frontal crash. The SRSCM determines if and when to deploy the PAB. ...

Other information:

Hyundai Tucson (LM) 2010-2015 Owners Manual: How vehicle audio works
AM and FM radio signals are broadcast from transmitter towers located around your city. They are intercepted by the radio antenna on your vehicle. This signal is then processed by the radio and sent to your vehicle speakers. When a strong radio signal has reached your vehicle, the precise engi ...

Hyundai Tucson (LM) 2010-2015 Service Manual: Clutch Pedal Repair procedures
Inspection Clutch Pedal Inspection 1. Measure the clutch pedal height (from the face of the pedal pad to the floor board) and the clutch pedal clevis pin play (measured at the face of the pedal pad.) Standard value Stroke (A): 150 ± 3 mm (5.9055 ± 0.118 in.) Free play (B): 6 ~ 13 m ...