Hyundai Tucson: Hydraulic System / Oil Cooler Repair procedures

Hyundai Tucson (LM) 2010-2015 Service Manual / Automatic Transaxle System / Hydraulic System / Oil Cooler Repair procedures

Inspection

Radiator Cap Testing

1.	Remove the radiator cap, wet its seal with engine coolant, and then install it on a pressure tester.

2.	Apply a pressure of 93.16 ~ 122.58 kPa (0.95 ~ 1.25 kgf/cmx, 13.51 ~ 17.78 psi).

3.	Check for a drop in pressure.

4.	If the pressure drops, replace the cap.

Radiator Leakage Test

1.	Wait until engine is cool, then carefully remove the radiator cap and fill the radiator with engine coolant, then install it on the pressure tester (A).

2.	Apply a pressure tester to the radiator and apply a pressure of 93.16 ~ 122.58 kPa (0.95 ~ 1.25 kgf/cmx, 13.51 ~ 17.78 psi).

3.	Inspect for engine coolant leaks and a drop in pressure.

Remove the tester and reinstall the radiator cap.

Check for engine oil in the coolant and/or coolant in the engine oil.

Removal and Installation

1.	Disconnect the battery negative terminal.

2.	Remove the air cleaner assembly. (Refer to Intake and exhaust system in this group)

Remove the under cover (A).

Tightening torque:

19.6 ~ 24.5 N.m (2.0 ~ 2.5 kgf.m, 14.5 ~ 18.1 lb-ft)

Loosen the drain plug (A), and drain the coolant.

Remove the radiator cap to speed draining.

Never remove the radiator cap when the engine is hot. Serious scalding could be caused by hot fluid under high pressure escaping from the radiator.

5.	Remove the radiator upper hose (A).

6.	Remove the radiator lower hose (A).

Disconnect the fan motor connector (A) and then remove the cooling fan assembly.

Tightening torque:

8.8 ~ 10.8 N.m (0.9 ~ 1.1 kgf.m, 6.5 ~ 7.9 lb-ft)

8.	Remove the front bumper. (Refer to BD group)

9.	Disconnect the over flow hose (A) from the radiator.

10.	Remove the cover (A) and the air guard (B) and then separate the condenser from the radiator.

11.

Remove the radiator mounting bracket (A) and then pull the radiator upper from vehicle.

Tightening torque:

8.8 ~ 10.8 N.m (0.9 ~ 1.1 kgf.m, 6.5 ~ 7.9 lb-ft)

12.	Installation is in the reverse order of removal.

13.

Fill the radiator with coolant and check for leaks.

•	Bleed air from the cooling system.

-	Start engine and let it run until it warms up. (Until the radiator fan operates 3 or 4 times.)

-	Turn off engine and let it cool dwon. Check the coolant level and add coolant if needed. This will allow trapped air to be removed from the cooling system.

-	Put the radiator cap on tightly, then run engine again and check for leaks.

Oil Cooler Components and Components Location

Components 1. Cooling fan assembly2. Radiator3. Mounting insulator4. Radiator upper mounting bracket5. Radiator upper hose6. Radiator lower hose7. Reservoir tank8. Over flow hose9. ATF cool ...

Oil Pump Description and Operation

Description The oil pump is built-in as a single unit with the 2/6 brake chamber. Rotation of the pump builds the hydraulic pressure needed for the lubrication of the various parts of the trans ...

Other information:

Hyundai Tucson (LM) 2010-2015 Service Manual: TJ Joint Repair procedures
Removal • Special grease must be applied to the driveshaft joint. Do not substitute with another type of grease. • The boot band should be replaced with a new one. 1. Remove the Front Driveshaft. (Refer to Driveshaft Assembly - “Front Driveshaft”) ...

Hyundai Tucson (LM) 2010-2015 Service Manual: Front Wiper Motor Components and Components Location
Component Location 1. Cap2. Nut3. Wiper arm & blade4. Retainer5. Cowl top cover6. Bolt7. Wiper motor & linkage assembly8. Wiper motor connector ...