Hyundai Tucson: Exterior / Hood Repair procedures

Replacement
Hood Assembly Replacement
   
When removing and installing the hood, an assistant is necessary.
Take care not to damaged the hood and body.
When removing the clips, use a clip remover.
1.
Loosen the hood hinge (A) mounting bolts, remove the hood (B).

Tightening torque:
21.6 ~ 26.5 N.m (2.2 ~ 2.7 kgf.m 15.9 ~ 19.5 lb-ft )

2.
Install in the reverse order of removal.
   
Make sure the hood locks/unlocks and opens/closes properly.
Adjust the hood alignment.
Hood Insulator Pad Replacement
   
Take care not to scratch the hood panel.
1.
Using a clip remover, remove the clips.
2.
Remove the hood insulator pad (A).

3.
Install in the reverse order of removal.
   
Replace any damaged clips.
Hood Seal Weatherstrip Replacement
1.
Detach the clips, then remove the hood weatherstrip (A).
   
Take care not to scratch the hood seal weatherstrip.

2.
Install in the reverse order of removal.
   
Replace any damaged clips.
Hood Weatherstrip Replacement
1.
Remove the hood weatherstrip (A).

2.
Install in the reverse order of removal.
Hood Latch Release Handle Replacement
1.
Remove the hood release handle (A).

2.
Install in the reverse order of removal.
   
Make sure the hood latch release cable is connected properly.
Make sure the hood locks/unlocks and opens/closes properly.
Hood Latch Replacement
1.
Loosen the hood latch (A) mounting bolts.
2.
Disconnect the hood latch cable (B) and release cable (C).

Tightening torque :
7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft )

3.
Install in the reverse order of removal.
   
Make sure the hood latch release cable is connected properly.
Make sure the hood locks/unlocks and opens/closes properly.
Adjust the latch alignment.
Adjustment
Adjust Hood
1.
After loosening the hinge (A) mounting bolt, adjust the hood (B) by moving it up or down, or right or left.
2.
Adjust the hood height by turning the hood over slam bumpers (C).
3.
After loosening the hood latch (D) mounting bolts, adjust the latch by moving it up or down, or right or left.

Fender Repair procedures
Replacement     • When removing and installing the hood, an assistant is necessary. • Be careful not to damage the hood and body. • When removing the clips, u ...

Tail Gate Repair procedures
Replacement Tail Gate Trim Replacement     • When prying with a flat-tipped screwdriver, wrap it with protective tape, and apply protective tape around the related parts, ...

Other information:

Hyundai Tucson (LM) 2010-2015 Service Manual: Engine Control Module (ECM) Schematic Diagrams
ECM Terminal And Input/Output signal [M/T] ECM Terminal Function (M/T) Connector [C200-MA] Pin No.DescriptionConnected to1Injector (Cylinder #3) [High] control outputInjector (Cylinder #3)2Injector (Cylinder #4) [High] control outputInjector (Cylinder #4)3Injector (Cylinder #2) [Low] contro ...

Hyundai Tucson (LM) 2010-2015 Service Manual: Rear Glass Defogger Printed Heater Repair procedures
Inspection     Wrap tin foil around the end of the voltmeter test lead to prevent damaging the heater line. Apply finger pressure on the tin foil, moving the tin foil along the grid line to check for open circuits. 1. Turn on the defogger switch and use a voltmeter to me ...

© 2010-2024 www.htmanual.net