Hyundai Tucson: Seat Belt / Front Seat Belt Repair procedures

Replacement
Front Seat Belt Replacement [General]
   
When installing the belt, make sure not to damaged the pretensioner.
1.
Remove the following items first :
A.
Front door scuff trim
(Refer to Interior - "Interior Trim")
B.
Rear door scuff trim
(Refer to Interior - "Interior Trim")
2.
After raise the lower anchor cover (A), loosen the lower anchor (B) mounting bolt.

Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft )

3.
Remove the center lower pillar trim (A).

4.
Remove the cap.
5.
After loosening the mounting bolt, then remove the center upper pillar trim (A) .

6.
After loosening the mounting bolt, then remove the upper anchor (A).

Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft )

7.
After disconnecting the pretensioner connector lock pin, remove the pretensioner connector (B), loosen the mounting bolt, then remove the pretensioner (A).

Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft )

8.
Install in the reverse order of removal.
Front Seat Belt Replacement [Europe]
   
When installing the belt, make sure not to damaged the pretensioner.
1.
Remove the following items first :
A.
Front door scuff trim
(Refer to Interior - "Interior Trim")
B.
Rear door scuff trim
(Refer to Interior - "Interior Trim")
2.
Using a screwdriver or remover (B), remove the lower anchor (A).

3.
Remove the center lower pillar trim (A).

4.
Remove the cap.
5.
After loosening the mounting bolt, then remove the center upper pillar trim (A) .

6.
After loosening the mounting bolt, then remove the upper anchor (A).

Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft )

7.
After disconnecting the pretensioner connector lock pin, remove the pretensioner connector (B), loosen the mounting bolt, then remove the pretensioner (A).

Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft )

8.
Install in the reverse order of removal.
Height Adjust Relacement
1.
Remove the following items first :
A.
Front door scuff trim
(Refer to Interior - "Interior Trim")
B.
Rear door scuff trim
(Refer to Interior - "Interior Trim")
C.
Front seat belt lower anchor
D.
Front seat belt upper anchor
E.
Center lower pillar trim
(Refer to Interior - "Interior Trim")
F.
Center upper fillar trim
(Refer to Interior - "Interior Trim")
2.
After loosening the mounting bolt, then remove the hight adjustor (A).

Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft )

3.
Install in the reverse order of removal.
   
Replace ant damaged clips.
Make sure the height adjust properly.
Front Seat Belt Buckle Relacement
1.
Remove the front seat.
(Refer to Seat & Power Seat - "Front Seat")
2.
After loosening the mounting bolt, then remove the front seat belt buckle (A).

Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)

3.
Install in the reverse order of removal.
Components and Components Location
Components 1. Front seat belt2. Height adjuster3. Rear seat belt4. Rear center seat belt buckle ...

Rear Seat Belt Repair procedures
Replacement Secondary Seat Belt Relacement     • When installing the belt, make sure not to damaged the retractor. 1. Remove the rear seat. (Refer to Seat & Power ...

Other information:

Hyundai Tucson (LM) 2010-2015 Owners Manual: Key ignition switch
WARNING NEVER turn the ignition switch to the LOCK or ACC position while the vehicle is in motion except in an emergency. This will result in the engine turning off and loss of power assist for the steering and brake systems. This may lead to loss of directional control and braking functi ...

Hyundai Tucson (LM) 2010-2015 Service Manual: Oil level sensor Repair procedures
Removal and Installation [For Europe] When the oil sensor signal fault occurs, refer to the DTC guide. 1. Drain the engine oil. 2. Remove the oil level sensor (A) after disconnecting the oil level sensor connector. Tightening torque: 8.8 ~ 9.8N.m (0.9 ~ 1.0kgf.m, 6.5 ~ 7.2lb-ft) ...

© 2010-2024 www.htmanual.net