Hyundai Tucson: Smart Key System / Smart Key Unit Repair procedures

Hyundai Tucson (LM) 2010-2015 Service Manual / Body Electrical System / Smart Key System / Smart Key Unit Repair procedures

Removal

Smart Key Unit

1.	Disconnect the negative (-) battery terminal.

2.	Remove the glove box housing. (Refer to the BD group - "Crash pad")

3.	After disconnecting the smart key unit connector (A), loosen the smart key unit mounting bolts, and remove the smart key unit (B).

RF Receiver

1.	Disconnect the negative (-) battery terminal.

2.	Remove the glove box housing. (Refer to the BD group - "Crash pad")

3.	Remove the air vent housing in front of the assist seat. (Refer to the BD group - "Crach pad")

4.	After loosening the mounting nut (B), disconnect the connector (A) and remove the receiver (C).

Interior 1 Antenna

1.	Disconnect the negative (-) battery terminal.

2.	Remove the seat heater switch assembly. (Refer to the BE group - "Seat heater")

After loosening the antenna nuts (2EA) and connector (B), remove the interior 1 antenna (A).

Release the connector lock (A) as indicated by the arrow, and then push-down the lock.

Make sure the connector is locked completely when installing.

Interior 2 Antenna

1.	Disconnect the negative (-) battery terminal.

Remove the floor console rear panel (A) using the appropriate tool.

Take care not to damage and scratch the floor console rear panel and its related parts.

Take care not to damage the hook when removing the floor console rear panel.

After loosening the antenna nuts (2EA) and connector, remove the interior 2 antenna (A).

Release the connector lock (A) as indicated by the arrow, and then push-down the lock.

Make sure the connector is locked completely when installing.

Interior 3 Antenna

1.	Disconnect the negative (-) battery terminal.

2.	After loosening the mounting bolts, then remove the rear seat assembly. (Refer to the BD group - "Rear seat")

After loosening the antenna nuts (2EA) and connector (A), remove the interior 3 antenna (B).

Release the connector lock (A) as indicated by the arrow, and then push-down the lock.

Make sure the connector is locked completely when installing.

Exterior Bumper Antenna

1.	Disconnect the negative (-) battery terminal.

2.	Lift the vehicle up using the lift. (Refer to the GI group - "Lift And Support Points")

3.	Disconnect the antenna connector (A) on the center of rear bumper.

4.	After loosening the nuts (2EA), remove the exterior bumper antenna (B).

Buzzer

1.	Disconnect the negative (-) battery terminal.

2.	Remove the front left fender. (Refer to the BD group - "Fender")

3.	Disconnect the connectors, then remove the buzzer (A).

Door Outside Handle

1.	Disconnect the negative (-) battery terminal.

2.	Disconnect the connector after removing the door trim. (Refer to the BD group - "Front door")

3.	After loosening the mounting bolt, then remove the key holder (A).

4.	Remove the outside handle (A) by sliding it rearward.

5.	Disconnect the outside handle connector (B).

Liftgate Switch

1.	Disconnect the negative (-) battery terminal.

2.	Remove the liftgate trim. (Refer to the BD group - "Liftgate trim")

3.	Disconnect the connector. After loosening the liftgate garnish mounting nuts (13EA), remove the liftgate garnish (A).

4.	Remove the outside handle (A) after loosening the outside handle mounting screws.

5.	Remove the other wiring connectors which connected with outside handle, then remove the liftgate switch assembly (A).

Inspection

Smart Key Unit

-	Refer to BE group - inspection / self diagnosis with scan tool.

Smart Key Switch

-	Refer to BE group - inspection / self diagnosis with scan tool.

Antenna

-	Refer to BE group - inspection / self diagnosis with scan tool.

Liftgate Switch

1.	Check for continuity between the liftgate latch terminals.

2.	If continuity is not specified, inspect the switch

Installation

Smart Key Unit

1.	Install the smart key unit.

2.	Install the smart key unit mounting bolt and nut, and then connect the connector.

3.	Install the glove box.

4.	Install the negative (-) battery terminal and check the smart key system.

RF Receiver

1.	Install the RF receiver.

2.	Install the glove box housing and air vent housing.

3.	Install the negative (-) battery terminal and check the smart key system.

Interior 1 Antenna

1.	Install the interior 1 antenna.

2.	Install the front seat heater switch assembly.

3.	Install the negative (-) battery terminal and check the smart key system.

Interior 2 Antenna

1.	Install the interior 2 antenna.

2.	Install the floor console rear cover after connecting the connector.

3.	Install the negative (-) battery terminal and check the smart key system.

Interior 3 Antenna

1.	Install the interior 3 antenna.

2.	Install the rear seat assembly.

3.	Install the negative (-) battery terminal and check the smart key system.

Exterior Bumper Antenna

1.	Install the exterior bumper antenna.

2.	Install the negative (-) battery terminal and check the smart key system.

Buzzer

1.	Install the buzzer.

2.	Install the front left fender.

3.	Install the negative (-) battery terminal and check the smart key system.

Door Outside Handle

1.	Install the outside handle.

2.	Install the door trim.

3.	Install the negative (-) battery terminal and check the smart key system.

Liftgate Switch

1.	Install the liftgate switch.

2.	Install the liftgate garnish.

3.	Install the liftgate trim.

4.	Install the negative (-) battery terminal and check the smart key system.

Smart Key Unit Schematic Diagrams

Circuit Diagram ...

Smart Key Diagnostic Repair procedures

Inspection Self Diagnosis With GDS Smart key system defects can be quickly diagnosed with the GDS. GDS operates actuator quickly to monitor, input/output value and self diagnosis. The followi ...

Other information:

Hyundai Tucson (LM) 2010-2015 Service Manual: Canister Close Valve (CCV) Repair procedures
Inspection 1. Turn the ignition switch OFF. 2. Disconnect the CCV connector. 3. Measure resistance between the CCV terminal 1 and 2. 4. Check that the resistance is within the specification. Specification: Refer to "Specification" 5. Disconnect the vapor hose connected with ...

Hyundai Tucson (LM) 2010-2015 Service Manual: Compass Mirror Repair procedures
Adjustment Calibration procedure If the display read "C", calibrate the compass. 1. Driving the vehicle in a circle at less than 8km/h 3 times or until the compass heading appears. 2. Driving in a circle in right-handed direction and opposite direction are possible, and if the calibratio ...