Hyundai Tucson: Rear Glass Defogger / Rear Glass Defogger Printed Heater Repair procedures
Hyundai Tucson (LM) 2010-2015 Service Manual / Body Electrical System / Rear Glass Defogger / Rear Glass Defogger Printed Heater Repair procedures
| Inspection |
Wrap tin foil around the end of the voltmeter test lead to
prevent damaging the heater line. Apply finger pressure on the tin foil,
moving the tin foil along the grid line to check for open circuits. |
| 1. |
Turn on the defogger switch and use a voltmeter to measure
the voltage of each heater line at the glass center point. If a voltage
of approximately 6V is indicated by the voltmeter, the heater line of
the rear window is considered satisfactory.
|
| 2. |
If a heater line is burned out between the center point and (+) terminal, the voltmeter will indicate 12V.
|
| 3. |
If a heater line is burned out between the center point and (-) terminal, the voltmeter will indicate 0V.
|
| 4. |
To check for open circuits, slowly move the test lead in the
direction that the open circuit seems to exist. Try to find a point
where a voltage is generated or changes to 0V. The point where the
voltage has changed is the open-circuit point.
|
| 5. |
Use an ohmmeter to measure the resistance of each heater line
between a terminal and the center of a grid line, and between the same
terminal and the center of one adjacent heater line. The section with a
broken heater line will have a resistance twice as that in other
sections. In the affected section, move the test lead to a position
where the resistance sharply changes.
|
Repair Of Broken Heater Line
Prepare the following items :
| 1. |
Conductive paint. |
| 2. |
Paint thinner. |
| 3. |
Masking tape. |
| 4. |
Silicone remover. |
| 5. |
Using a thin brush :
Wipe the glass adjacent to the broken heater line, clean with
silicone remover and attach the masking tape as shown. Shake the
conductive paint container well, and apply three coats with a brush at
intervals of about 15 minutes apart. Remove the tape and allow
sufficient time for drying before applying power. For a better finish,
scrape away excess deposits with a knife after the paint has completely
dried. (Allow 24 hours).
|
Components and Components Location
Component Location
1. Rear glass defogger relay2. Rear glass defogger switch3. Rear glass defogger
...
Rear Glass Defogger Switch Repair procedures
Removal
1.
Disconnect the negative (-) battery terminal.
2.
Remove the right air vent.
(Refer to BD group - "Crash pad")
3.
Remove the rear glass defogger switch (A).
[LHD]
[RHD]
...
Other information:
Hyundai Tucson (LM) 2010-2015 Service Manual: Rear Lower Arm Repair procedures
Replacement
1.
Remove the rear wheel & tire.
Tightening torque :
88.3 ~ 107.9N.m (9.0 ~ 11.0kgf.m, 65.1 ~ 79.6lb-ft)
Be careful not to damage to the hub bolts when removing the rear wheel & tire.
2.
Loosen the nut and then remove the rear stabilizer li ...
Hyundai Tucson (LM) 2010-2015 Service Manual: Components and Components Location
Component Location (1)
1. Head lamp (High/Low)2. Front turn signal lamp3. Position lamp4. Front fog lamp5. Door mirror turn signal lamp6. Overhead console lamp7. Room lamp8. Vanity lamp9. Side marker
Component Location (2)
1. Turn signal lamp2. Back up lamp3. Tail/stop lamp4. Stop lamp5. ...
© 2010-2024 www.htmanual.net
