Hyundai Tucson: Charging System / Alternator Repair procedures

Hyundai Tucson (LM) 2010-2015 Service Manual / Engine Electrical System / Charging System / Alternator Repair procedures

Removal

1.	Turn ignition switch OFF and disconnect the negative (-) battery cable.

2.	Remove the drive belt. (Refer to Engine Mechanical System - "Drive Belt")

3.	Disconnect the alternator connector (A) and the cable (B) from alternator "B" terminal.

4.	Pull out the through bolt and then remove the alternator (A).

Installation

1.	Install in the reverse order of removal.

Adjust the alternator belt tension after installation.

(Refer to Engine Mechanical System - "Drive Belt")

Alternator installation bolt:

[M10] 29.4 ~ 41.2 N.m (3.0 ~ 4.2 kgf.m, 21.7 ~ 30.4 Ib-ft)

[M8] 21.6 ~ 32.4 N.m (2.2 ~ 3.3 kgf.m, 15.9 ~ 23.9 Ib-ft)

Alternator brace mounting bolt:

21.6 ~ 32.4 N.m (2.2 ~ 3.3 kgf.m, 15.9 ~ 23.9 Ib-ft)

Disassembly

1.	Remove the rear cover (A) after removing nuts (B).

2.	Remove the mounting bolts (A) and the regulator assembly (B).

3.	Remove the slip ring guide (A) after pulling it.

Remove the OAD(Overrunning Alternator Decoupler) cap.

•	When installing, replace with new OAD cap.

5.	Remove the OAD(Overrunning Alternator Decoupler) pulley (A) using the special tool.

6.	Unsolder the 3 stator leads (A).

7.	Remove the 4 through bolts (A).

8.	Disconnect the rotor (A) and housing (B).

Reassembly

Reassemble in the reverse order of disassembly.

•	When reassembling OAD pulley, replace with new OAD cap.

Inspection

[Rotor]

1.	Check that there is continuity between the slip rings (C).

2.	Check that there is no continuity between the slip rings and the rotor (B) or rotor shaft (A).

3.	If the rotor fails either continuity check, replace the alternator.

[Stator]

1.	Check that there is continuity between each pair of leads (A).

2.	Check that there is no continuity between each lead and the coil core.

3.	If the coil fails either continuity check, replace the alternator.

Alternator Schematic Diagrams

Circuit Diagram • COM signal - When controlling the voltage generated, the ECM sends the target voltage data to the alternator via a PWM signal.(High voltage: 4V or h ...

Battery Description and Operation

Description 1. The CMF(Closed Maintenance Free) battery is, as the name implies, totally maintenance free and has no removable battery cell caps. 2. The CMF(Closed Maintenance Free) batter ...

Other information:

Hyundai Tucson (LM) 2010-2015 Owners Manual: Turn signals and lane change signals
To signal a turn, move the lever up for a right turn or down for a left turn to position (A). The lever will return to the OFF position when the turn is completed. To signal a lane change, move the lever slightly and hold it in position (B). The lever will return to the OFF position when re ...

Hyundai Tucson (LM) 2010-2015 Service Manual: Rear Glass Defogger Printed Heater Repair procedures
Inspection Wrap tin foil around the end of the voltmeter test lead to prevent damaging the heater line. Apply finger pressure on the tin foil, moving the tin foil along the grid line to check for open circuits. 1. Turn on the defogger switch and use a voltmeter to me ...