Hyundai Tucson: Driveshaft Assembly / Front Driveshaft Repair procedures

Removal
1.
Remove the front wheel and tire (A) from front hub .

Tightening torque:
88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft)

   
Be careful not to damage to the hub bolts when removing the front wheel and tire (A).

2.
Remove the coking nut (A).

Tightening torque:
294.2 ~ 313.8 N.m (30.0 ~ 32.0 kgf.m, 217.0 ~ 231.5 lb-ft)

   
The front hub coking nut should be replaced with new ones.
After installation coking nut (A), stake the coking nut using a chisel and hammer as shown in the illustration below.

3.
Remove the brake hose (A) and wheel speed sensor (B).

Tightening torque:
6.8 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 7.9 lb-ft)

4.
Remove the tie rod end ball joint (C) from the knuckle.
(1)
Remove the split pin (A).
(2)
Remove the castle nut (B).

Tightening torque:
23.5 ~ 33.3 N.m (2.4 ~ 3.4 kgf.m, 17.4 ~ 24.6 lb-ft)

5.
Remove the lower arm (A) mounting bolt and nut from the knuckle.

Tightening torque:
98.0 ~ 117.6 N.m (10.0 ~ 12.0 kgf.m, 72.3 ~ 86.7 lb-ft)

6.
Using a plastic hammer (A), disconnect driveshaft (C) from the axle hub (B).

7.
Loosen the inner shaft mounting bolts and then disconnect the inner shaft (A).

Tightening torque:
49.0 ~ 68.6 N.m (5.0 ~ 7.0 kgf.m, 36.2 ~ 50.6 lb-ft)

   
By the shape and the engine bracket bolts are mounted differently.

8.
Insert a pry bar (A) between the transaxle case and joint case, and separate the drive shaft (B) from the transaxle case.

9.
Install in the reverse order of removal.
   
Use a pry bar being careful not to damage the transaxle and joint.
Do not insert the pry bar too deep, as this may cause damage to the oil seal.
Do not pull the driveshaft by excessive force it may cause components inside the joint kit to dislodge resulting in a torn boot or a damaged bearing.
Plug the hole of the transaxle case with the oil seal cap to prevent contamination.
Support the driveshaft properly.
Replace the retainer ring whenever the driveshaft is removed from the transaxle case.
10.
Check the front alignment.
(Refer to Suspension System - "Front Alignment")
Front Driveshaft Components and Components Location
Components [THETA II 2.4 2WD] 1. Driveshaft (LH)2. Driveshaft (RH) [NU 2.0 / THETA II 2.4 4WD] 1. Driveshaft (LH)2. Inner shaft bearing bracket3. Driveshaft (RH) Components [LH] ...

TJ Joint Components and Components Location
Components [LH] 1. BJ assembly 2. BJ circlip 3. BJ boot band 4. BJ boot 5. Shaft6. TJ boot band7. TJ boot8. Spider assembly9. Retainer ring10. TJ housing11. Housing circlip [RH] 1. BJ ...

Other information:

Hyundai Tucson (LM) 2010-2015 Service Manual: Transmitter Specifications
Specifications ItemSpecificationRated voltageDC 3VTemperature range-4°F ~ 140°F (-20°C ~ +60°C)RF Modulation methodFSKKeyless entry transmitterPower sourceLithium 3V battery (1EA)Transmissible distance30m or moreLife of battery2 years or more (at 20 times per day)Button3 (Door lock, Door un ...

Hyundai Tucson (LM) 2010-2015 Service Manual: Engine Control Module (ECM) Schematic Diagrams
ECM Terminal And Input/Output signal [M/T] ECM Terminal Function (M/T) Connector [C200-MA] Pin No.DescriptionConnected to1Injector (Cylinder #3) [High] control outputInjector (Cylinder #3)2Injector (Cylinder #4) [High] control outputInjector (Cylinder #4)3Injector (Cylinder #2) [Low] contro ...

© 2010-2024 www.htmanual.net