Hyundai Tucson: Electric Power Steering / Steering Column and Shaft Repair procedures

Replacement
1.
Disconnect the battery negative cable from the battery and then wait for at least 30 seconds.
2.
Turn the steering wheel so that the front wheels can face straight ahead.
3.
Remove the airbag module (A).
(Refer to Restraint - "Airbag Module")

4.
Disconnect the connector (B) & lock nut (A) and then remove the steering wheel from the steering column shaft.

   
Do not hammer on the steering wheel to remove it; it may damage the steering column.
5.
Remove the steering column upper (A) and lower (B) shroud.

6.
Remove the clock spring (A).

7.
Remove the multifunction switches (A).

8.
Remove the lower crash pad.

9.
Loosen the bolt & nut and then remove the panel (A).

10.
Loosen the nut and then dust cover (A).

11.
Loosen the bolt (A) and then disconnect the universal joint assembly from the pinion of the steering gear box.

Tightening torque :
32.4 ~ 37.3 N.m (3.3 ~ 3.8 kgf.m, 23.9 ~ 27.5 lb-ft)

   
Keep the neutral-range to prevent the damage of the clock spring inner cable when you handle the steering wheel.
12.
Disconnect all connectors connected the steering column.
13.
Remove the steering column by loosening the mounting bolts (A) and nuts (B).

Tightening torque :
12.7 ~ 17.7N.m (1.3 ~ 1.8kgf.m, 9.4 ~ 13.0lb-ft)

14.
Installation is the reverse of the removal.
15.
Conduct the "ASP Calibration" and "EPS Type Recognition" by GDS.
(Refer to Electric Power Steering - "ASP calibration or EPS type recognition")
16.
Conduct the "MDPS TEST (Motor Driven Power Steering)" by GDS.
(Refer to Electric Power Steering - "MDPS Performance Inspection")
Disassembly
Universal joint assembly
1.
Loosen the bolt (A) and then disconnect the universal joint assembly from the steering column assembly.

Tightening torque :
28.0 ~ 32.0 N.m ( 2.8 ~ 3.2 kgf.m, 20.3 ~ 23.1 lb-ft)

2.
Reassembly is the reverse of the disassembly.
Inspection
1.
Check the steering column for damage and deformation.
2.
Check the join bearing for damage and wear.
3.
Check the tilt bracket for damage and cracks.
4.
Check the key lock assembly for proper operation and replace it if necessary.
Repair procedures
General Inspection After or before servicing the EPS system, perform the troubleshooting and test procedure as follows. Compare the system condition with normal condition in the table below and ...

Steering Gear box Components and Components Location
Components 1. Tie rod end2. Lock nut3. Bellows 4. Bellows band5. Tie rod6. Rack bar 7. Dust packing 8. Dust cap 9. Oil seal10. Pinion plug11. Pinion assembly12. Yoke plug13. Yoke spring14. Suppo ...

Other information:

Hyundai Tucson (LM) 2010-2015 Service Manual: Repair procedures
Inspection Manual Transaxle Oil Inspection 1. Park the vehicle on a level ground and stop the engine. 2. Retighten the oil filler plug (A) with a new washer. 3. Check level with finger.     Oil level must be up to fill the hole, if not, add oil until it runs over. ...

Hyundai Tucson (LM) 2010-2015 Owners Manual: Climate control air cleaner
Filter inspection The climate control air filter should be replaced according to the Maintenance Schedule. If the vehicle is operated in severely air-polluted cities or on dusty rough roads for a long period, it should be inspected more frequently and replaced earlier. When you replace the c ...

© 2010-2024 www.htmanual.net