Replacement |
1. |
Remove the front wheel & tire.
|
2. |
Disconnect the stabilizer link (B) with the front strut assembly (A) after loosening the nut.
|
3. |
Remove the sprit pin and castle nut and then disconnect the tie-rod end (A) from the front knuckle.
|
4. |
Loosen the bolt & nutand then remove the lower arm (A).
|
5. |
Loosen the nut and then remove the dust cover (A). |
6. |
Loosen the bolt (A) and then disconnect the universal joint assembly from the pinion of the steering gear box.
|
7. |
Loosen the bolt (A) & nut (B) and then remove the roll rod stopper.
|
8. |
Disconnect the muffler rubber hanger (A). |
9. |
Loosen the bolts & nuts and then remove the sub frame.
|
10. |
Loosen the bolt & nut and then remove the protactor (A). |
11. |
Loosen the bolt and then remove the stabilizer (A) from the sub frame.
|
12. |
Loosen the bolt and then remove the steering gear box (A).
|
13. |
Installation is the reverse of the removal. |
Disassembly |
1. |
Fix the steering gear box assembly (A) on the vice. |
2. |
Remove the bellows clip (A) in the direction of the arrow. (The left and right same work.) |
3. |
Give space to bellows bend (B) by using the ring pliers (A). (The left and right same work) |
4. |
After making the space to the bellows and tie-rod end contact
part by using the (-) driver, remove the bellows (A) in the direction
of the arrow. (The left and right same work) |
5. |
Remove the tie-rod & tie-rod end assembly (A). (The left and right same work) |
6. |
After fixing the yoke plug (A), remove the rock nut (B). |
7. |
Remove the yoke plug (A). |
8. |
Remove the yoke spring (A) and leaf spring (B).
|
9. |
Remove the support yoke assembly (A) from the inner lack hosing.
|
10. |
Remove the dust packing & cap (A). |
11. |
Remove the top plug (A) by using the spanner.
|
12. |
Remove the pinion assembly (A). |
13. |
Remove the rack bar (A) in the direction of the arrow. |
Reassembly |
1. |
After spreading grease on the rack bar gear part (A), install rack bar (B) in the direction of the arrow.
|
2. |
After spreading grease on the pinion gear part, install the pinion assembly (A). |
3. |
After spreading three bond (Loctite) on the top plug (A) thread, install the top plug by using the spanner.
|
4. |
Install the dust packing & cap (A). |
5. |
Install the support yoke (A).
|
6. |
Install the Yoke plug (A) and leaf spring (B).
|
7. |
After spreading three bond (Loctite) on the Yoke plug (A) thread, install the Yoke plug. |
8. |
Adjust Yoke with reference to the “How to adjust Yoke”.
(Refer to Electric Power Steering - "Steering Gear Box") |
9. |
After fixing the yoke plug, install the rock nut (A). |
10. |
Install the tie-rod & tie-rod end assembly (A). (The left and right same work) |
11. |
Caulk (A) the rack bar and tie-rod assembly joints. (The left and right same work)
|
12. |
After spreading sealant on the rack hosing and the bellow joints (A), install the bellows (B) in the direction of the arrow. |
Inspection |
1. |
Rack bar
|
2. |
Pinion assembly
|
3. |
Check the inside of rack housing for damage. |
4. |
Check the bellows for being torn. |
Hyundai Tucson (LM) 2010-2015 Service Manual: Accelerator Pedal Repair procedures
Removal
1.
Turn the ignition switch OFF and disconnect the negative (-) battery cable.
2.
Disconnect the accelerator position sensor connector (A).
3.
Remove the installation nuts (B), the bolt (C) and then remove the accelerator pedal module.
Installation
1.
Install in the revers ...
Hyundai Tucson (LM) 2010-2015 Owners Manual: To increase cruise control speed
Push the lever (1) up (to RES+) and hold it, while monitoring the SET speed
on the instrument cluster. Release the lever when the desired speed is shown
and the vehicle will accelerate to that speed.
Push the lever (1) up (to RES+) and release it immediately. The cruising
speed wil ...