Hyundai Tucson: Airbag Module / Driver Airbag (DAB) Module and Clock Spring Repair procedures

Hyundai Tucson (LM) 2010-2015 Service Manual / Restraint / Airbag Module / Driver Airbag (DAB) Module and Clock Spring Repair procedures

Removal

1.	Disconnect the battery negative cable and wait for at least three minutes before beginning work.

2.	Remove the airbag module mounting bolts (2EA).

3.	Remove the wiring fixing clip (C) and disconnect the horn connector (A).

Release the connector locking pin, then disconnect the driver airbag module connector (B).

The removed airbag module should be stored in aclean, dry place with the pad cover facing up.

5.	Remove the steering wheel and steering wheel column cover. (Refer to the Steering System group- Steering Column and Shaft)

6.	Disconnect the clock spring and horn connector, then remove the clock spring.

Inspection

Driver Airbag (DAB)

If any improper parts are found during the following inspection, replace the airbag module with a new one.

Never attempt to measure the circuit resistance of the airbag module (squib) even if you are using the specified tester. If the circuit resistance is measured with a tester, accidental airbag deployment will result in serious personal injury.

1.	Check pad cover for dents, cracks or deformities.

2.	Check the airbag module for denting, cracking or deformation.

3.	Check hooks and connectors for damage, terminals for deformities, and harness for binds.

4.	Check airbag inflator case for dents, cracks or deformities.

5.	Install the airbag module to the steering wheel to check for fit or alignment with the wheel.

Clock Spring

1.	If, as a result of the following checks, even one abnormal point is discovered, replace the clock spring with a new one.

2.	Check connectors and protective tube for damage, and terminals for deformities.

Installation

1.	Remove the ignition key from the vehicle.

2.	Disconnect the battery negative cable from battery and wait for at least three minutes before beginning work.

3.	Connect the clock spring harness connector and horn harness connector to the clock spring.

4.	Set the center position by setting the marks between the clock spring and the cover into line. Make an array the mark (xx) by turning the clock spring clockwise to the stop and then 2.0 revolutions counterclockwise.

5.	Install the steering wheel column cover and the steering wheel. (Refer to the Steering System group- Steering Column and Shaft)

6.	Connect the Driver Airbag (DAB) module connector and horn connector, and then install the Driver Airbag (DAB) module on the steering wheel.

Secure the Driver Airbag (DAB) with the new mounting bolts.

Tightening torque:

7.8 ~ 10.8 N.m (0.8 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)

8.	Connect the battery negative cable.

After installing the airbag, confirm proper system operation:

A.	Turn the ignition switch ON; the SRS indicator light should be turned on for about six seconds and then go off.

B.	Make sure horn button works.

Driver Airbag (DAB) Module and Clock Spring Components and Components Location

Components 1. Driver Airbag (DAB)2. Steering Wheel3. Clock Spring ...

Passenger Airbag (PAB) Module Description and Operation

Description The passenger airbag (PAB) is installed inside the crash pad and protects the front passenger in the event of a frontal crash. The SRSCM determines if and when to deploy the PAB. ...

Other information:

Hyundai Tucson (LM) 2010-2015 Owners Manual: Emergency tailgate safety release
Your vehicle is equipped with an Emergency Tailgate Safety Release lever located inside on the bottom of the tailgate. When someone is inadvertently locked in the luggage compartment, the tailgate can be opened by moving the lever in the direction of the arrow and pushing the tailgate open ...

Hyundai Tucson (LM) 2010-2015 Service Manual: SS-B Solenoid Valve(ON/OFF) Repair procedures
Inspection 1. Turn ignition switch OFF. 2. Disconnect the solenoid valve connector. 3. Measure resistance between sensor signal terminal and sensor ground terminal. 4. Check that the resistance is within the specification. Removal 1. Remove the air cleaner assembly and air d ...