Hyundai Tucson: Fuses And Relays / Relay Box (Passenger Compartment) Description and Operation

Hyundai Tucson (LM) 2010-2015 Service Manual / Body Electrical System / Fuses And Relays / Relay Box (Passenger Compartment) Description and Operation

Description
SJB (Smart Junction Box)
1.
Specification
Item
Requirement
Remark
Rated voltage
DC 12V
x
Voltage range
DC 8 ~ 16V
Normal operating in this range
Storage temperature
-40°C ~ +95°C
x
Operating temperature
-30°C ~ +85°C
x
Operating humidity
85%
PCB, Damp proofing, Coating, etc.
Dark current
Max. 200uA
All Load Open
Operation Voltage Range
DC 8 ~ 16V
Should activate normally in normal range
Max Use Humidity
85%
Regulated together with parts needing insulation such as PCB, damp-proofing, coating, etc
Insulation Resistance
Should be no ignition caused by electrical shorts


2.
Rated Burden
Item
Rated Burden
Head Lamp Low LH
55W
Head Lamp Low RH
55W
Head Lamp High LH
60W (Max)
Head Lamp High RH
60W (Max)
Tail Lamp LH
41W(Max)
Tail Lamp RH
31W(Max)
Front Fog Lamp LH+RH
54W
Interior Lamp
45W
B/Alarm Start Relay Coil Control
0.9W
RR FOG Relay Coil Control
0.6W
Lift Gate Latch or Luggage Room Lamp (Power Lift Gate) Relay Coil Control
0.6W
Back Up Relay Coil Control
0.45W
RR Wiper Relay Coil Control (External)
12W (Output Max)
B/Alarm Horn Relay Coil Control (External)
12W (Output Max)
RR.HTD Relay Coil Control (External)
12W (Output Max)
Front Deicer Relay Coil Control (External)
12W (Output Max)

3.
Block Diagram

4.
SJB Main Functions
(1)
Lamp control and wire protection through IPS .
(2)
When Reference Voltage exceeded, PWM normal voltage control to prevent lamp loss or damage
(3)
CAN outpout for switch signal input .
(4)
Diagnosis using CAN (Short to GND, Open Circuit)
(5)
Fail Safe lamp control.
NO
Section
Content
1
Enter Input SW
Receive switch input and send switch status as CAN message to each module
2
Lamp Control (IPS)
Receive commands from BCM as CAN message to control Lamps with IPS
3
Internal Relay Control
Receive commands from BCM as CAN message and control relays in the IP Box
T/Gate latch, B/Alarm start, Backup, Rear Fog lamp 
4
External Relay Control
Receive commands from BCM as CAN message and control relays outside of the IP Box
B/Alarm horn, Rear Wiper motor, Rear deffogger, Front deicer
5
Low Power Mode
(Sleep Mode)
When there is no change in the CAN message or switch input for 5 seconds, converts to low-power mode (sleep mode)
6
WakeUp Mode
When there is a change in the CAN message or Input switch in low-power mode, converts to normal mode
7
Output status send
Lamps and Rear Fog output status sent to BCM as CAN message
8
H/W Rescure
When MCU fails, and Head Lamp Low Switch is input, Head Lamp Low Beam activates

5.
Network

6.
CAN input & output flow

Relay Box (Passenger Compartment) Components and Components Location
Component Location ...

Relay Box (Passenger Compartment) Repair procedures
Inspection Fuse 1. Be sure there is no play in the fuse holders, and that the fuses are held securely. 2. Are the fuse capacities for each circuit correctx 3. Are there any blown fusesx ...

Other information:

Hyundai Tucson (LM) 2010-2015 Service Manual: Components and Components Location
Component Location 1. Driver power window switch2. Assist power window switch3. SJB (Smart Junction Box)4. Door lock switch5. Liftgate lock actuator & switch6. Front door lock actuator & switch7. Rear door lock actuator & switch ...

Hyundai Tucson (LM) 2010-2015 Owners Manual: Fuel filler door
Opening the fuel filler door The fuel filler door must be opened from inside the vehicle by pulling up the fuel filler door opener lever. 1. Turn the engine off. 2. Pull the fuel filler door opener lever up located on the floor, left side of the driver’s seat. ✽ NOTICE If the fuel f ...

© 2010-2024 www.htmanual.net