Hyundai Tucson: SRSCM / Side Impact Sensor (SIS) Repair procedures

Hyundai Tucson (LM) 2010-2015 Service Manual / Restraint / SRSCM / Side Impact Sensor (SIS) Repair procedures

Removal

Pressure Side Impact Sensor

•	Removal of the airbag must be performed according to the precautions/procedures described previously.

•	Before disconnecting the side impact sensor connector(s), disconnect the side airbag connector(s).

•	Do not turn the ignition switch ON and do not connect the battery cable while replacing the side impact sensor.

1.	Disconnect the battery negative cable, and wait for at least three minutes before beginning work.

2.	Remove the front door trim. (Refer to the Body group- Front door)

3.	Disconnect the front side impact sensor connector and remove the front side impact sensor mounting screws.

4.	Remove the screw gromments (A).

Side Impact Sensor

1.	Disconnect the battery negative cable and wait for at least three minutes before beginning work.

2.	To remove the seat belt anchor pretensioner (C), keep on pushing the lock pins (A) as arrow direction. And then remove the seat belt after pushing the lock pin (B).

3.	Remove the door scuff trim. (Refer to the Body group - Interior trim)

4.	Remove the center pillar trim. (Refer to the Body group - Interior trim)

5.	Disconnect the side impact sensor connector.

6.	Loosen the side impact sensor mounting bolt and remove the side impact sensor.

Installation

Pressure Side Impact Sensor

•	Do not turn the ignition switch ON and do not connect the battery cable while replacing the side impact sensor.

Install the screw gromments (A).

•	Do not reuse the screw grommets (A), whenever installing.

Install the new front side impact sensor with the screws then connect the pressure side impact sensor connector.

Tightening torque:

1.1 ~ 1.3 N.m (0.11 ~ 0.13 kgf.m, 0.7 ~ 1.0 lb-ft)

3.	Install the front door trim. (Refer to the Body group- Front door)

4.	Reconnect the battery negative cable.

After installing the front side impact sensor, confirm proper system operation:

A.	Turn the ignition switch ON; the SRS indicator light should be turned on for about six seconds and then go off.

•	You must comply with the specified tightening torques with the tool specified because Pressure – Side Impact Sensors (P-SIS) may be broken or screw gromment may be rotated.

•	Problems may be occurred in the durability of P-SIS or impact sensing performance may be depreciated if screw gromment is rotated.

•	The door module must not be transformed because SRSCM judges a impact through the pressure sensed in the door module.

Side Impact Sensor

•	Do not turn the ignition switch ON and do not connect the battery cable while replacing the side impact sensor.

Install the new side impact sensor with the bolt then connect the side impact sensor connector.

Tightening torque:

7.0 ~ 9.0 N.m (0.7 ~ 0.9 kgf.m, 5.1 ~ 6.6 lb-ft)

2.	Install the center pillar trim (Refer to the Body group - Interior tirm)

3.	Install the door scuff trim. (Refer to the Body group - Interior tirm)

Insert the seat belt to the anchor pretensioner.

Make sure the lock pin is connected in properly.

5.	Reconnect the battery negative cable.

After installing the Side Impact Sensor, confirm proper system operation:

A.	Turn the ignition switch ON; the SRS indicator light should be turned on for about six seconds and then go off.

Side Impact Sensor (SIS) Components and Components Location

Components ...

Seat Belt Buckle Switch (BS) Description and Operation

Description The SRSCM shall monitor the status of the driver and front passenger seat belt buckle. The SRSCM provides one pin each for the driver and front passenger seat belt buckle status inp ...

Other information:

Hyundai Tucson (LM) 2010-2015 Owners Manual: Sound Settings
Press the key Select [Sound] through TUNE knob or key Select menu through TUNE knob Sound Settings This menu allows you to set the ‘Bass, Middle, Treble’ and the Sound Fader and Balance. Select [Sound Settings] Select menu through TUNE knob Turn T ...

Hyundai Tucson (LM) 2010-2015 Owners Manual: To increase cruise control speed
Push the lever (1) up (to RES+) and hold it, while monitoring the SET speed on the instrument cluster. Release the lever when the desired speed is shown and the vehicle will accelerate to that speed. Push the lever (1) up (to RES+) and release it immediately. The cruising speed wil ...