Hyundai Tucson: Rear Glass Defogger / Rear Glass Defogger Printed Heater Repair procedures
Hyundai Tucson (LM) 2010-2015 Service Manual / Body Electrical System / Rear Glass Defogger / Rear Glass Defogger Printed Heater Repair procedures
| Inspection |
Wrap tin foil around the end of the voltmeter test lead to
prevent damaging the heater line. Apply finger pressure on the tin foil,
moving the tin foil along the grid line to check for open circuits. |
| 1. |
Turn on the defogger switch and use a voltmeter to measure
the voltage of each heater line at the glass center point. If a voltage
of approximately 6V is indicated by the voltmeter, the heater line of
the rear window is considered satisfactory.
|
| 2. |
If a heater line is burned out between the center point and (+) terminal, the voltmeter will indicate 12V.
|
| 3. |
If a heater line is burned out between the center point and (-) terminal, the voltmeter will indicate 0V.
|
| 4. |
To check for open circuits, slowly move the test lead in the
direction that the open circuit seems to exist. Try to find a point
where a voltage is generated or changes to 0V. The point where the
voltage has changed is the open-circuit point.
|
| 5. |
Use an ohmmeter to measure the resistance of each heater line
between a terminal and the center of a grid line, and between the same
terminal and the center of one adjacent heater line. The section with a
broken heater line will have a resistance twice as that in other
sections. In the affected section, move the test lead to a position
where the resistance sharply changes.
|
Repair Of Broken Heater Line
Prepare the following items :
| 1. |
Conductive paint. |
| 2. |
Paint thinner. |
| 3. |
Masking tape. |
| 4. |
Silicone remover. |
| 5. |
Using a thin brush :
Wipe the glass adjacent to the broken heater line, clean with
silicone remover and attach the masking tape as shown. Shake the
conductive paint container well, and apply three coats with a brush at
intervals of about 15 minutes apart. Remove the tape and allow
sufficient time for drying before applying power. For a better finish,
scrape away excess deposits with a knife after the paint has completely
dried. (Allow 24 hours).
|
Components and Components Location
Component Location
1. Rear glass defogger relay2. Rear glass defogger switch3. Rear glass defogger
...
Rear Glass Defogger Switch Repair procedures
Removal
1.
Disconnect the negative (-) battery terminal.
2.
Remove the right air vent.
(Refer to BD group - "Crash pad")
3.
Remove the rear glass defogger switch (A).
[LHD]
[RHD]
...
Other information:
Hyundai Tucson (LM) 2010-2015 Service Manual: Specifications
Specifications
Fuel Delivery System
ItemsSpecificationFuel TankCapacity58x (15.3 U.S.gal., 61.3 U.S.qt., 51.0 Imp.qt.)Fuel FilterTypePaper typeFuel PressureLow Pressure Fuel Line495 ~ 505 kPa (4.9 ~ 5.1 kgf/cmx, 71.8 ~ 73.2 psi)High Pressure Fuel Line2.0 ~ 15.0 MPa (20.4 ~ 153.0 kgf/cmx, 290 ...
Hyundai Tucson (LM) 2010-2015 Owners Manual: Locking
To lock :
1. Close all doors, engine hood and tailgate.
2. Either press the door handle button or press the Door Lock button (1) on the
smart key.
3. The hazard warning lights will blink and the chime will sound once.
4. Make sure the doors are locked by checking the position of the door l ...
© 2010-2025 www.htmanual.net