Hyundai Tucson: Seat Belt / Front Seat Belt Repair procedures

Replacement
Front Seat Belt Replacement [General]
   
When installing the belt, make sure not to damaged the pretensioner.
1.
Remove the following items first :
A.
Front door scuff trim
(Refer to Interior - "Interior Trim")
B.
Rear door scuff trim
(Refer to Interior - "Interior Trim")
2.
After raise the lower anchor cover (A), loosen the lower anchor (B) mounting bolt.

Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft )

3.
Remove the center lower pillar trim (A).

4.
Remove the cap.
5.
After loosening the mounting bolt, then remove the center upper pillar trim (A) .

6.
After loosening the mounting bolt, then remove the upper anchor (A).

Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft )

7.
After disconnecting the pretensioner connector lock pin, remove the pretensioner connector (B), loosen the mounting bolt, then remove the pretensioner (A).

Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft )

8.
Install in the reverse order of removal.
Front Seat Belt Replacement [Europe]
   
When installing the belt, make sure not to damaged the pretensioner.
1.
Remove the following items first :
A.
Front door scuff trim
(Refer to Interior - "Interior Trim")
B.
Rear door scuff trim
(Refer to Interior - "Interior Trim")
2.
Using a screwdriver or remover (B), remove the lower anchor (A).

3.
Remove the center lower pillar trim (A).

4.
Remove the cap.
5.
After loosening the mounting bolt, then remove the center upper pillar trim (A) .

6.
After loosening the mounting bolt, then remove the upper anchor (A).

Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft )

7.
After disconnecting the pretensioner connector lock pin, remove the pretensioner connector (B), loosen the mounting bolt, then remove the pretensioner (A).

Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft )

8.
Install in the reverse order of removal.
Height Adjust Relacement
1.
Remove the following items first :
A.
Front door scuff trim
(Refer to Interior - "Interior Trim")
B.
Rear door scuff trim
(Refer to Interior - "Interior Trim")
C.
Front seat belt lower anchor
D.
Front seat belt upper anchor
E.
Center lower pillar trim
(Refer to Interior - "Interior Trim")
F.
Center upper fillar trim
(Refer to Interior - "Interior Trim")
2.
After loosening the mounting bolt, then remove the hight adjustor (A).

Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft )

3.
Install in the reverse order of removal.
   
Replace ant damaged clips.
Make sure the height adjust properly.
Front Seat Belt Buckle Relacement
1.
Remove the front seat.
(Refer to Seat & Power Seat - "Front Seat")
2.
After loosening the mounting bolt, then remove the front seat belt buckle (A).

Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)

3.
Install in the reverse order of removal.
Components and Components Location
Components 1. Front seat belt2. Height adjuster3. Rear seat belt4. Rear center seat belt buckle ...

Rear Seat Belt Repair procedures
Replacement Secondary Seat Belt Relacement     • When installing the belt, make sure not to damaged the retractor. 1. Remove the rear seat. (Refer to Seat & Power ...

Other information:

Hyundai Tucson (LM) 2010-2015 Service Manual: Rear Stabilizer Bar Repair procedures
Replacement 1. Remove the rear wheel & tire. Tightening torque : 88.3 ~ 107.9N.m (9.0 ~ 11.0kgf.m, 65.1 ~ 79.6lb-ft)     Be careful not to damage to the hub bolts when removing the rear wheel & tire. 2. Loosen the nut and then remove the rear stabilizer li ...

Hyundai Tucson (NX4) 2022-2023 Owner's Manual: Fuses
A vehicle’s electrical system is protected from electrical overload damage by fuses. This vehicle has 2 (or 3) fuse panels, one located in the driver’s side panel bolster, the other in the engine compartment. If any of your vehicle’s lights, accessories, or controls do not work, ...

© 2010-2023 www.htmanual.net