Hyundai Tucson: Seat & Power Seat / Front Seat Repair procedures

Hyundai Tucson (LM) 2010-2015 Service Manual / Body (Interior and Exterior) / Seat & Power Seat / Front Seat Repair procedures

Replaccement

Seat Assembly Replacement

1.	Remove the seat mounting cover.

After loosening the seat assembly mounting bolts, remove the seat assembly (A).

Tightening torque :

44.1 ~ 58.8N.m (4.5 ~ 6.0kgf.m, 32.5~43.4 lb-ft )

3.	Disconnect the connector (A), and wirering (B).

Install in the reverse order of removal.

SEAT MOUNTING BOLT INSTALLATION PROCEDURE

•	Set the into the most rearward position. Check then each slide is locked, and then Tighten the front mounting bolt temporarily.

•	Set the seat into most forward position. Check that each slide is locked, and then Tighten the rear mounting bolt completely.

•	Set the seat into the most rearward position. Check the front mounting bolt completely.

•	Check that the seat operates to and fro smoothy and the locking portion locks properly.

Shield Cover Replacement

1.	Remove the silde switch (A) and recliner switch (B).

2.	Using a screwdriver, remove the front shield cover (A).

3.	Using a screwdriver remove the shield cover (A).

4.	Disconnect the connector (A).

5.	Install in the reverse order of removal.

Seat Back Replacement

•	Replace the seat back assembly if active head rest system is equipped.

1.	Remove the front seat assembly.

2.	Remove the headrest.

Push the clips (B) from the seat back cover (A).

•	Push the middle area of clip using the flat head screwdriver.

•	Be careful not to damage the clip.

4.	Push the hooks (A), from the seat back frame.

5.	Disconnect the connector (A) mounting clip.

6.	Pull out the headrest guides (A) while pinching the end of the guides, and remove them.

7.	Remove the seat back from the frame.

8.	After removing the hogring clips (B) on the front of seat back and remove the seat back cover (A).

Install in the reverse order of removal.

•	To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the hogring clips (A).

•	Replace the hogring clips with new ones using special tool (C) (09880-4F000).

Seat Cushion Cover Replacement

1.	Remove front seat assembly.

2.	Remove the shield cover.

3.	Push the hook (A), remove the seat cushion (C).

4.	Disconnect the connector (A).

After removing the hogring clip (B) on the front of seat cushion and remove the seat cushion cover (A).

•	When removing the hog-ring clip, remove the hog-ring clip with pressing the wire not to separate the wire from the sponge.

Install in the reverse order of removal.

•	To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the hogring clips (A).

•	Replace the hogring clips with new ones using special tool (C) (09880-4F000).

Seat Frame Replacement

Remove the following items:

A.	Front seat assembly

Seat back

C.	Seat cushion

Headrest

2.	After loosening the mounting screw, then remove the front inside shield cover (A).

After loosening the mounting bolts, then disconnect the seat back frame (A) and seat cushion frame (B).

•	Remove the side air bag for replacing side air bag installation seat.

•	Before service, be fully aware of precautions and service procedure relevant to air bag (Refer to page RT-Airbag)

Tightening torque :

44.1 ~ 58.8 N.m (4.5 ~ 6.0 kgf.m, 32.5 ~ 43.4 lb-ft)

4.	Install in the reverse order of removal.

Front Seat Components and Components Location

Components 1. Headrest2. Headrest guide3. Seat back cover4. Seat back heater5. Seat back pad6. Power rumber support assembly7. Seat cushion cover8. Seat cushion heater9. Seat cushion pad10. Shiel ...

Rear Seat Components and Components Location

Components 1. Headrest2. Headrest guide3. Upper bezel4. Tether anchor garnish5. Armrest cover6. Seat back cover7. Armrest8. Seat cushion cover9. Seat warmer10. Seat cushion pad ...

Other information:

Hyundai Tucson (LM) 2010-2015 Service Manual: Special Service Tools
Special Service Tools Tools(Number and name)IllustrationUse09200-3N000Engine support fixture(Beam)Removal and installation of the transaxle.Use this beam (SST No. : 09200-38001/09200-3N000) with the supporter (SST No. : 09200-2S000).09200-2S000Engine support fixture(Adapter)Removal and installa ...

Hyundai Tucson (LM) 2010-2015 Service Manual: Transmitter Specifications
Specifications ItemSpecificationRated voltageDC 3VTemperature range-4°F ~ 140°F (-20°C ~ +60°C)RF Modulation methodFSKKeyless entry transmitterPower sourceLithium 3V battery (1EA)Transmissible distance30m or moreLife of battery2 years or more (at 20 times per day)Button3 (Door lock, Door un ...